 | | | Re-ordering custom parameters within sets | Re-ordering custom parameters within sets 2004-05-11 - By stefan@(protected)
Back
also, this is a trick...
1.) Edit the PPG as suggested by other people (and install
it)
2.) DONT SAVE THE SCENE
3.) Open the scene again after you edited the SPDL
viola! the PPG now has changed the order. And if you had
saved the scene it would have lost the connections to the
objects.
Also play around with creating tabs and groups to further
clean up the PPG.
for instance (taken from my head)
Group "Eye Lids
{
"Right_Lid";
"Left_Lid";
}
That would (if I typed it correct) create a group around the
sliders you made. I don't have XSI in front of me now, so
there might be typos. But I'm sure you can find some info
about it on XSIbase. I think "AliT" made a tutorial about
it, also known as SheepFactory.
best of luck!
stefan andersson
Rick Walia <xsilist@(protected)> wrote:
> SPDL hack! It'll grow hair on your chest :)
>
> It shouldn't be that difficult. Just edit the bottom part
of the spdl file
> where
> it says layout. Order them anyway you like.
> I think there is a tutorial on the SI tutorials bank in
regards to this.
>
> /R
>
>
> Quoting Matt Morris <matt@(protected)>:
>
> > Thanks Sandy,
> > was hoping I could get away with a drag and drop
somewhere but sounds like I
> > should get to grips with this spdl...
> >
> > Matt
> >
> > -- --Original Message-- --
> > From: owner-xsi@(protected)
[mailto:owner-xsi@(protected)]On Behalf
> > Of Sandy Sutherland
> > Sent: 11 May 2004 11:24
> > To: XSI@(protected)
> > Subject: Re: Re-ordering custom parameters within sets
> >
> >
> > You have to install an SPDL for it, and then edit the
SPDL - not very
> > difficult and it allows you to create funcky layouts for
your Custom PPGS!
> >
> > See page 332 in your fundamentals manual!
> >
> > s.
> >
> >
-- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- -----
> > Sandy Sutherland Digital Doodeller/Technical Director
> > The Refinery (Cape) http://www.refinery.co.za
> > mailto:sandy@(protected)
> > (P) (+27 21) 480 3132 (F) (+27 21) 480 3101
> >
-- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- -----
> > -- -- Original Message -- --
> > From: "Matt Morris" <matt@(protected)>
> > To: <XSI@(protected)>
> > Sent: Tuesday, May 11, 2004 12:15 PM
> > Subject: Re-ordering custom parameters within sets
> >
> >
> > > Hi All,
> > >
> > > I was wondering whether anyone could tell me how to
re-order custom
> > > parameters inside a custom pset once it has been
created? I have a new
> > > parameter which I would like to appear further up the
list...
> > >
> > > Any help appreciated,
> > > Matt
> > >
> > >
> > > ---
> > > Unsubscribe? Mail Majordomo@(protected) with the
following text in body:
> > > unsubscribe xsi
> >
> > ---
> > Unsubscribe? Mail Majordomo@(protected) with the
following text in body:
> > unsubscribe xsi
> >
> >
> > ---
> > Unsubscribe? Mail Majordomo@(protected) with the
following text in body:
> > unsubscribe xsi
> >
>
>
>
> ---
> Unsubscribe? Mail Majordomo@(protected) with the
following text in body:
> unsubscribe xsi
>
---
Unsubscribe? Mail Majordomo@(protected) with the following text in body:
unsubscribe xsi
|
|
|