 | | | Curve snapping? | Curve snapping? 2003-12-01 - By Julian Baum
Back
Yep, that's the one......works for me.
The only bit of voodoo you may need to do is to slide the manip along the
curve a little to get the CV to snap in the first place. Curve snapping is
not as responsive as point snapping. Not for me anyway, but then I only use
three chickens.
Julian.
on 2/12/03 4:07 AM, Tereza P. Flaxman wrote:
> Take a dead chicken, swing it around your head three times. Select the CV
> you want to snap and using the middle mouse click and drag
> on the curve you want to snap to. It should work. If it does not work try
> more chickens.
>
>
> On Tue, 2 Dec 2003, Anthony Rosbottom wrote:
>
>> ok, cheers for that, next problem - how do people get the curve snapping
>> working without pulling all their hair out???!!
>> I can get it working at certain times but it's extremely finicky and
>> awkward to use. I'm just trying to snap the end CV of one curve onto an
>> arbitary mid-point of another curve.
>>
>> Is there any 'curve snapping voodoo' I need to invoke ??!
>>
>> At 00:52 02/12/2003, Daniel Corcoran wrote:
>>> Just open the attribute editor and look in 'nurbs surface history'!
>>>
>>> Cheers
>>>
>>> DAN
>>>
>>> -- --Original Message-- --
>>> From: Anthony Rosbottom [mailto:bliz@(protected)]
>>> Sent: Tuesday, 2 December 2003 11:30 AM
>>> To: maya@(protected)
>>> Subject: How do I find out the # of spans in a curve?
>>>
>>>
>>> I've got some curves that are birail 3+ profiles and I'm going cross-eyed,
>>> counting the spans of each curve myself.
>>> Is there a mel command that reports the number of spans in a selected curve
>>> or is there some other way of finding out that isn't obvious to me?
>>>
>>> Cheers,
>>> Bliz::..
>>>
>>> www.bliz.co.uk
>>>
>>>
>>>
>>> -- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---
>>> List-help: <mailto:listar@(protected)?Subject=help>
>>> List-unsubscribe: <http://www.highend3d.com/maya/listserver/>
>>> List-subscribe: <http://www.highend3d.com/maya/listserver/>
>>> List-archive: <http://www.highend3d.com/maya/archive/>
>>>
>>>
>>> ************************************************************************
>>> CAUTION - This message may contain privileged and confidential
>>> information intended only for the use of the addressee named above.
>>> If you are not the intended recipient of this message you are hereby
>>> notified that any use, dissemination, distribution or reproduction of
>>> this message is prohibited. If you have received this message in error
>>> please notify AMCOR immediately.
>>> Any views expressed in this message are those of the individual sender
>>> and may not necessarily reflect the views of AMCOR.
>>> ************************************************************************
>>>
>>>
>>> -- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---
>>> List-help: <mailto:listar@(protected)?Subject=help>
>>> List-unsubscribe: <http://www.highend3d.com/maya/listserver/>
>>> List-subscribe: <http://www.highend3d.com/maya/listserver/>
>>> List-archive: <http://www.highend3d.com/maya/archive/>
>>
>> Cheers,
>> Bliz::..
>>
>> www.bliz.co.uk
>>
>>
>>
>> -- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---
>> List-help: <mailto:listar@(protected)?Subject=help>
>> List-unsubscribe: <http://www.highend3d.com/maya/listserver/>
>> List-subscribe: <http://www.highend3d.com/maya/listserver/>
>> List-archive: <http://www.highend3d.com/maya/archive/>
>>
>>
>
>
> -- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---
> List-help: <mailto:listar@(protected)?Subject=help>
> List-unsubscribe: <http://www.highend3d.com/maya/listserver/>
> List-subscribe: <http://www.highend3d.com/maya/listserver/>
> List-archive: <http://www.highend3d.com/maya/archive/>
>
-- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---
List-help: <mailto:listar@(protected)?Subject=help>
List-unsubscribe: <http://www.highend3d.com/maya/listserver/>
List-subscribe: <http://www.highend3d.com/maya/listserver/>
List-archive: <http://www.highend3d.com/maya/archive/>
|
|
|